Better Health Through Better Knowledge

Switch to desktop Register Login

Get a Thick V Taper Back with Bent Over Rows

Rate this item
(1 Vote)

Muscles Worked in Bent Over Row for Back  

Target Muscles

  • Deltoids
  • Erector spinae
  • Upper back


  • Trapezius, Middle
  • Trapezius, Lower
  • Rhomboids
  • Latissimus Dorsi
  • Teres Major
  • Deltoid, Posterior
  • Infraspinatus
  • Teres Minor
  • Brachialis
  • Brachioradialis
  • Pectoralis Major, Sternal

Dynamic Stabilizers

  • Biceps Brachii
  • Triceps, Long Head


  • Erector Spinae
  • Hamstrings
  • Gluteus Maximus
  • Adductor Magnus  

How to Properly Perform the Bent Over Row for Back

  1. Make sure your head is parallel to the ground and centered over your shoulders.
  2. Bring your chest up.
  3. As you bring your chest up, your shoulders must relax and not go up. Therefore, relax your shoulders down and back.
  4. Tighten your abs by pulling your belly button to your spine.
  5. Align your knees with your second and third toes.
  6. Make sure your knees are not locked. There must always be a slight bend in them.
  7. Stand with your feet spaced comfortably apart (usually hip width).
  8. Stand with your body weight placed at the mid points of your feet.  
After attaining the correct posture start doing the following steps. 
  1. Bend your torso over, keeping a natural arch in your spine, keeping your knees slightly bent.
  2. Keep your abdominal muscles tight, shoulders back and chest up.
  3. Take a big breath before pulling the weight to your chest. Breathe on the floor between reps.
  4. Don’t extend your hips too much. Your back shouldn’t rise much higher then where it was at the start of the Barbell Row
  5. Under control, pull the weight up to your lower chest (xiphoid process), while focusing on bringing your shoulder blades together. 
  6. Stop just after your elbow joints are in line with your shoulders and reverse the motion back down.
  7. Under control, lower the weight, stop just before your elbow joints are straight and reverse the motion back up.
  8. Repeat  

Tips for Maximizing the Muscle Building Effects of Bent Over Rows

  • Torso may be kept horizontal for stricter execution.
  • Knees are bent in effort to keep low back straight.
  • If low back becomes rounded due to tight hamstrings, either knee should be bent more or torso may not be positioned as low.
  • If low back is rounded due to poor form, dead lift weight to standing position and lower torso into horizontal position with knees bent and back straight.
  • A shoulder width or underhand grip can increase lat involvement by emphasizing shoulder extension over transverse extension.
  • Don’t pull with your hands. Pull your elbows to the ceiling. Try to make your shoulder-blades touch & open your chest.
  • The bar starts on the floor on each rep. Don’t overdo the hip extension.
  • Don’t try to hold the bar against your chest.
  • Don’t try to return the bar slowly to the floor.

Common Errors While Performing the Bent Over Row 

  • Bar Too Far Away. Keep the bar close to your body. Put the bar over your feet, straight under your shoulder-blades.    
  • Back Going Vertical. It’s not a Deadlift. Your upper-back should do the work, not your hips. Lower the weight if you extend your hips too much.   
  • Dropping the Chest. You’ll drop your chest to meet the bar when the weight gets heavy. Lower the weight when this gets excessive.   
  • Extending the Knees. Use hip extension on the way up, but no knee extension. Keep your knees unlocked but straight.

Variations of the Bent Over Row

Variations are intended to work different subgroups of muscles, or work the same muscles in slightly different ways. There are plenty of variations to the exercise. Some other variations include: 

  • Dumbbell Bent Over Row. Same movements as as detailed above.
  • Pendlay Row. Pendlay Rows involve arching of your upper-back.
  • Reverse-grip Row. Using an underhand grip. Works biceps more.

 Additional Exercises for the Back

These exercises will help develop a big and powerful back when used with the bent over rows:

  • Lat bar Pulldown
  • Machine Seated Row
  • Seated Cable Rows 
  • Lat Bar Pulldown
  • Reverse Lat Bar Pulldown
  • Hyperextensions
  • Deadlifts
Last modified on Friday, 16 December 2011 16:33
Login to post comments

External links are provided for reference purposes. The World News II is not responsible for the content of external Internet sites. Template Design © Joomla Templates | GavickPro. All rights reserved.

Top Desktop version